随着罗茨风机使用时间的增加，设备出现故障的几率也会随着增大，从新设备购买后的安装、设备日常维护以及设备检修，都有些事项需要注意，做好风机安装、日常维护、保养检修等工作，不仅能防患于未然，还能能让风机处于更好的运行状态，延长风机使用寿命。我们对罗茨风机需要注意的事项在此做一下小结。

       With the increase of the service time of Roots blower, the probability of equipment failure will also increase. There are somematters needing attention in the installation, routine maintenance and overhaul of the equipment after the purchase of new equipment. Doing a good job in the installation, routine maintenance, maintenance and repair of the fan can not only prevent the trouble in the bud, but also make the fan in a better operation state, Prolong the service life of fan. We need to pay attention to the items of Roots blower here to make a summary.

　　一、关于罗茨风机的安装：

　　1.请不要把罗茨鼓风机安装在人员经常出入、通过的场所，避免磕碰或因设备高温被烫伤。

　　2.风机房内请设置通风换气扇，当温度超过40℃，将会较大缩短风机和电机的使用寿命，尤其在夏季高温时，有必要时请选择水冷罗茨风机。

　　3.请不要把风机安装在含有**溶剂、易燃性气体和腐蚀性气体的场所，以防火灾或中毒。　　

　　I. installation of Roots blower

　　1. Please do not install roots blower in the place where people often go in and out, so as to avoid bumping or scalding due to high temperature of the equipment.

　　2. Please install ventilation fan in the fan room. When the temperature exceeds 40 ℃, the service life of the fan and motor will be greatly shortened. Especially in summer when the temperature is high, please choose if necessary Water cooling of Roots blower 。

　　3. Please do not install the fan in the place containing organic solvent, flammable gas and corrosive gas to prevent fire or poisoning.

　　二、关于罗茨风机日常维护

　　1.罗茨风机每天启动时，按时检查油箱的位置和油质，及时添加或更换。

　　2.应根据风机使用的现场环境，如灰尘、粉尘和设备使用频率等，定期及时清洗和清理。

　　3.罗茨鼓风机新机运行一个月后需要换一次齿轮油，三个月后再更换新油，以后，换油周期可根据油品的质量确定，但不能超过半年。

　　4.新机运行24小时后，需调整三角皮带松紧一次，一周后再次调整，以后经常注意观察三角带，当发现风机异响、大电流，需要及时检查皮带松紧度。

　　2. Routine maintenance of Roots blower

　　1. When roots blower starts every day, check the position and quality of oil tank on time, and add or replace it in time.

　　2. The fan should be cleaned and cleaned regularly and timely according to the site environment, such as dust, dust and equipment frequency.

　　3. The gear oil of Roots blower needs to be changed once after one month of operation and three months later. After that, the oil change period can be determined according to the quality of the oil, but not more than half a year.

　　4. After the new machine runs for 24 hours, it is necessary to adjust the V-belt tightness once, and then adjust it again after a week. In the future, pay attention to observe the V-belt frequently. When abnormal noise and large current are found in the fan, the belt tightness should be checked in time.

　　三、关于罗茨风机的检修

　　1.对罗茨风机进行保养与检修时，须切断电源后进行。

　　2.非专业人员请不要擅自分解、拆解、修理和改造风机，若设备出现故障，请立即停机检查原因，并与厂家或经销商联系，请专业维修人员进行检修。

　　上海瑞柘环保设备集团是一家生产罗茨风机近15年的厂家，公司主要生产罗茨风机、真空风机(罗茨泵)、环形风机和漩涡风机、离心风机等鼓风机设备，提供服务，如果您有关于罗茨风机价格、罗茨风机选型、罗茨风机维修和罗茨风机售后等系列问题，都可以随时联系我们。

　　1.罗茨鼓风机的维护保养

　　(1)日常保养：日常工作中应注意轴承温度、声音、振动情况，检查油标油位，油温、进排气压力、电流表指数示等。

　　(2)每月检查：有三角带传动的风机应定期检查V带的张力。

　　(3)季度检查：每季度定期清洗过滤器，更换一次润滑油。

　　(4)年度检查：每年应定期清洗风机的齿轮、轴承、油密封、气密封。检查转子和气缸内部的情况，校正各部间隙。

　　2. 结论

　　罗茨鼓风机在连续使用过程中会出现不同程度的磨损，风机内腔转子与转子、转子与隔板之间的各间隙是影响风机正常运行的主要原因，所以在安装时调整风机内腔各间隙，定期润滑风机各润滑部位，避免出现因安装和润滑不良而出现风机无法正常运行的情况，就能很好地保证罗茨鼓风机的正常运行，以确保生产正常运行。罗茨鼓风机的日常维护：日常工作中要注意轴承的温度、声音、振动情况，检查油位、油温、进排气压力、电流表指数等。

       3. Maintenance of Roots blower

　　1. The roots blower must be maintained after the power is cut off.

　　2. Please do not disassemble, disassemble, repair and transform the fan without authorization. If the equipment fails, please stop the machine immediately to check the cause, and contact the manufacturer or dealer for maintenance.

　　Shanghai Ruizhe environmental protection equipment group is a manufacturer of Roots blower for nearly 15 years Roots Blower 、 Vacuum fan (roots pump) 、 Annular fan and Vortex fan 、 Centrifugal fan Wait for the blast Machine equipment, provide service if you have about Price of Roots blower 、 Selection of Roots blower 、 Roots blower maintenance And Roots fan after-sales and other issues, you can contact us at any time.

　　罗茨鼓风机的使用维护及保养

　　(1)所输送气体如含有杂质，必须预先加以净化，以免损坏零件及转子平衡。

　　(2)检查风机管道的安装是否符合要求，风机主轴的转向是否正确。

　　(3)检查稀油站与鼓风机、与高位油箱、与仪表盘及电器控制柜的连接是否正确，向稀油站油箱注人适量的32号或46号润滑油。

　　(4)先启动稀油站，查看润滑油是否足量连续地达到鼓风机左、右轴承位，确信润滑油已达到鼓风机左、右轴承位后，再启动电机(若电机轴承为滑动轴承，还必须保证润滑油足量连续地达到电机轴承位后方能启动电机)。

　　(5)开车前必须关闭进风口(或出风口阀门)，开车后逐渐打开，一直调到所需工况，但不得超过电机负荷。

　　(6)鼓风机运转时要注意风机和电机内部应无异响，是否漏油，是否有过大振动，轴承温升是否过高，电机电流是否过大，地脚松动等不正常现象，如果有上述现象应及时停车排除。

　　(7)不允许鼓风机在性能不稳定的喘振区域工作。

　　(8)应定期清除聚集在转子部分的气体杂质和污垢，以免影响转子平衡产生振动。

　　(9)拆卸转子须将机壳中分面及轴承上盖拆开后整体吊出，检查叶轮、叶片表面、密封圈、轴衬等零部件磨损情况，检查叶轮铆钉有无松脱，润滑系统是否可靠，以及管道接头有无渗漏。清除风机流道内积留的灰尘和油污。检查期限应根据情况拟订，但每年不得少于两次，每次检查应特别仔细，并做好记录。

　　(10)鼓风机长期不使用时，就定期将转子旋转120℃或180%，以防主轴弯曲。

　　(11)拆换轴承箱轴承时，应注意轴承装配位置，并按原位置装好。

　　(12)叶轮轮毅端面与密封条应保持间隙为0.07-0.巧mm，叶轮进口圈外面与密封条的间隙为0.1一0.2mm，间隙过大会产生泄漏。

Use and maintenance of Roots blower

　　(1) if the delivered gas contains impurities, it must be purified in advance to avoid damaging the balance of parts and rotors.

　　(2) check whether the installation of fan pipe meets the requirements and whether the rotation direction of fan spindle is correct.

　　(3) check whether the connection between the thin oil station and the blower, the high-level oil tank, the instrument panel and the electrical control cabinet is correct, and inject an appropriate amount of 32 or 46 lubricating oil into the oil tank of the thin oil station.

　　(4) start the thin oil station first, check whether the lubricating oil continuously reaches the left and right bearing positions of the blower, and then start the motor after making sure that the lubricating oil has reached the left and right bearing positions of the blower (if the motor bearing is a sliding bearing, it is also necessary to ensure that the lubricating oil continuously reaches the motor bearing position before starting the motor).

　　(5) before start-up, the air inlet (or outlet valve) must be closed, and it shall be opened gradually after start-up until the required working condition is reached, but the motor load shall not be exceeded.

　　(6) during the operation of the blower, attention should be paid to whether there is abnormal noise inside the fan and motor, whether there is oil leakage, whether there is excessive vibration, whether the temperature rise of bearing is too high, whether the motor current is too large, and the foundation is loose. If there are such abnormal phenomena, stop the machine in time to eliminate them.

　　(7) the blower is not allowed to work in the surge area with unstable performance.

　　(8) the gas impurities and dirt accumulated in the rotor should be removed regularly to avoid affecting the balance of the rotor and causing vibration.

　　(9) to dismantle the rotor, the casing split and bearing upper cover shall be removed and lifted out as a whole. The wear of impeller, blade surface, sealing ring and shaft lining shall be checked. The impeller rivet shall be checked for looseness, whether the lubrication system is reliable, and whether the pipe joint has leakage. Remove the dust and oil dirt in the fan channel. The inspection period shall be worked out according to the situation, but it shall not be less than twice a year. Each inspection shall be particularly careful and recorded.

　　(10) when the blower is not used for a long time, rotate the rotor at 120 ℃ or 180% regularly to prevent the main shaft from bending.

　　Pay attention to the original position of bearing box when assembling.

　　(12) the clearance between impeller hub end face and sealing strip should be 0.07-0 The clearance between the outside of impeller inlet ring and sealing strip is 0.1-0.2mm. If the clearance is too large, leakage will occur.

　　上海瑞柘环保设备集团有限公司生产的罗茨鼓风机拥有可靠的质量保障，广泛应用于工业环保、医药生产、污水处理、水产养殖、车船活鲜增氧、冶金业、石油开采、造纸、食品、矿山、塑料、煤气、钢铁、气力输送、农业灌溉等行业。“技术领先、质量**、用户至上”一直是守正的经营理念。为此，公司愿以真诚的合作态度、朴实的工作作风、优良的产品质量、及时周到的售后服务，与各界新老朋友同舟共济，携手开创美好的明天!

污水处理、水产养殖、车船活鲜增氧、冶金业、石油开采、造纸、食品、矿山、塑料、煤气、钢铁、气力输送、农业灌溉等行业。" style="margin: 0px; padding: 1px; font-family: "Microsoft YaHei"; -webkit-tap-highlight-color: rgba(255, 255, 255, 0); color: rgb(67, 67, 67); font-size: 15px; text-align: justify; white-space: normal; background: rgb(194, 217, 233);">       The roots blower produced by Shanghai Ruizhe Environmental Protection Equipment Group Co., Ltd. has reliable quality assurance and is widely used in industrial environmental protection, pharmaceutical production, sewage treatment, aquaculture, vehicle and ship fresh oxygen increasing, metallurgy, oil mining, paper making, food, mining, plastics, gas, steel, pneumatic conveying, agricultural irrigation and other industries. "Leading technology, quality * *, customer first" has always been the correct business philosophy. To this end, the company is willing to sincere cooperation attitude, simple style of work, good product quality, timely and thoughtful after-sales service, with new and old friends from all walks of life to join hands to create a better tomorrow!