罗茨风机间隙规范，罗茨风机叶轮与各组件的间隙尺寸。经过掌握这种尺寸能够在安装使用时运行融洽和平稳。

　　1、罗茨风机叶轮与叶轮的间隙尺寸：

　　这两个零配件中间的间隙在0.3mm~0.4mm

　　2、罗茨风机叶轮与外壳的间隙尺寸：

　　这两个零配件中间的间隙在0.1mm~0.2mm

　　3、罗茨风机叶轮与侧墙板的间隙尺寸：

　　这两个零配件中间的间隙在0.2mm~0.3mm

　　4、罗茨风机同歩齿轮的齿合间隙尺寸：

　　这两个零配件中间的间隙在0.07mm~0.15mm

　　这一尺寸针对生产厂家的工艺技术与技术性有一定的影响，技术成熟的离心风机厂家生产制造出的罗茨风机运行下去平稳，使用寿命长久。

　　风机叶片晃动间隙规范静态数据标准偏差为:叶轮与叶轮中间的间隙0.4-~0.5mm，叶轮与叶壳中间的轴向间隙0.2~0.3mm，叶轮与左、右墙板中间的径向间隙0.3~0.4mm(左墙板间隙务必超过右墙板间隙0.05mm之上)，同步齿轮的齿合间隙0.08~0.16mm

　　罗茨风机零配件间隙调节到是多少才好?

　　罗茨风机调节间隙，不一样地方的间隙规范是不一样的，只能在规范的范围之内，设备才可以平稳的运行。因此在调节零配件间隙的情况下要按照下列的规范来实际操作，外壳间隙操纵在0.20—0.395中间;叶轮—叶轮间隙操纵在0.29—0.34中间;叶轮与前墙板径向间隙操纵在0.12—0.18中间;叶轮与墙壁间隔应当在0.63—0.69范围之内。

　　The clearance specification of Roots blower, the clearance dimension between Roots blower impeller and each component. After mastering this size, it can run harmoniously and stably during installation and use.

　　Clearance standard for Roots blower accessories

　　1. Clearance dimension between Roots blower impeller and impeller:

　　The gap between the two parts is 0.3mm~0.4mm

　　2. Gap dimension between Roots blower impeller and housing:

　　The gap between the two parts is 0.1mm~0.2mm

　　3. Gap dimension between Roots blower impeller and side wall panel:

　　The gap between the two parts is 0.2mm~0.3mm

　　4. Backlash dimension of Roots blower synchronizing gear:

　　The clearance between the two parts is 0.07mm~0.15mm

　　This dimension has a certain impact on the process technology and technicality of the manufacturer. Roots fans manufactured by mature centrifugal fan manufacturers run smoothly and have a long service life.

　　The standard deviation of the static data of the fan blade shaking clearance specification is: the clearance between the impeller and the impeller is 0.4-~0.5mm, the axial clearance between the impeller and the blade shell is 0.2~0.3mm, the radial clearance between the impeller and the left and right wallboards is 0.3~0.4mm (the left wallboard clearance must exceed the right wallboard clearance by more than 0.05mm), and the meshing clearance of the synchronous gear is 0.08~0.16mm

　　What is the clearance of Roots blower parts?

　　The gap regulation of Roots blower is different in different places. The equipment can operate smoothly only within the range of the specification. Therefore, in the case of adjusting the clearance of parts and accessories, the actual operation shall be carried out according to the following specifications, and the clearance of the shell shall be controlled between 0.20-0.395; The clearance between impeller and impeller is between 0.29 and 0.34; The radial clearance between the impeller and the front wall panel is controlled between 0.12 and 0.18; The distance between the impeller and the wall shall be within the range of 0.63-0.69.